Top Notch Motorsports LLC

Click here to edit subtitle

Long Prairie Fair

Long Prairie MN on July 15th @ 7:00pm

Limited Weld - 1st $800, 2nd $500, 3rd $250, 4th $75  

Economy - 1st $800, 2nd $500, 3rd $250, 4th $75 

Builder Class - 1st $800, 2nd $500, 3rd $250, 4th $75

80's and newer "Chain Stock:- 1st $800, 2nd $500, 3rd $250, 4th $75

Chain Trucks - 1st $800, 2nd $500, 3rd $250,  4th $75

Entry $50 includes 1 pit person, extra pit pass $15

 

Limited Weld Class Rules

"Old iron and 80s and Newer will run together to these rules"

1.    Cage- Dash bar and behind seat bar and door bars allowed 2 inch min and 5inch max diameter and cannot be attached to frame. May have only 2 bars max behind seat in a crisscross pattern. Must be securely fastened or you will be told to remove. Dash bar may connect to the firewall in 2 spots 3inch by 1/4inch max flat stock and cannot be placed within the dp, mid plate or threaded rod that is used in the motor dept 1inch gap from all. If you have a dp or mid plate dash bar must be 6 inch away from firewall. If you have a tranny brace it must be mounted to cross member with factory tranny mount, free floating or 1 bolt and dash bar must be 2inches away from tranny tunnel. Halo bar no farther back then 15 inches from center post on 4 door cars or 8 inch on 2 door cars. Can be welded to frame and bolted to roof. Halo bar can be attached to the door bars. You can have 1 down bar 2inch max from the door bars only located within the front inside door seam and straight down to the frame. Can be welded to top side and cannot run down the side of frame. And 1 in the middle of the front door to sheet metal only. You can run a gas tank protector that must mount from the behind the seat bar 30inch wide and can go to the sheet metal but must be within the frame rails with no down bars and be off the floor 2inches.

2.    Doors- **Please reinforce your driver?s door very good, in this type of competition all drivers doors will take some type of hit during the event. We want you to be safe and protected behind your reinforcement. ** All doors may be welded solid with 3inch wide by 1/8inch thick strap or chained shut. Top of doors can be folded and welded together with no added metal.

3.    Hood and Trunk- Hood may be bolted in 8 spots, 4 to frame and 4 to sheet metal. The rod can go down the side of frame but must be vertical. Trunk lid may be welded solid with 3inch by 1/8inch thick strap or bolted every 3inch. Trunk may be bolted in 6 spots 4 to frame and 2 to sheet metal. Trunk may have a strap from bumper to the trunk no farther up than 6inch from lower trunk seam. You may tuck trunks. NO sedagons, decking must be removed.

4.    Seam welding- Frame can be welded fire wall forward top only. K-frame CAN be welded solid, May take out pucks and replace with 1inch bolts. You can have a 5 inch 2inch by 2inch angle iron to help hold tranny cross member on and cannot go to crush box or gusset or you will cut it off the frame to get it at the 5inch. Tranny cross member must be bolted to the 5 inch angle iron. No frame shaping. Sway bar can be welded in the front of car in factory spot the width of frame and cannot run down the frame.

5.    Body bolts- You may remove pucks front and back, you may add 1 extra body bolts per side which can go to frame with a max of 6inchx 6inch washer?s and a 1inch bolt washers cannot be welded to the sheet metal or frame. Tranny cross member can be a max of 2 by 3inch.

6.    Core support- Core support may have a 2 by 2 1/4inch angle iron on the top of core support from fender to fender. NO relocation of core support or mounts must be in factory spot. Radiator barrels are o.k. BUT must be factory size, CANNOT touch the frame in any way, CANNOT be welded to the angle iron at all, Bolted in 4 spots to core support or 4 -4inch welds to core support to hold it in place. Must run vent tub under the car! Radiators can have a guard in front but must be a max of 1/4inch and 1inch past the ac condenser opening and bolted in 4 spots.

7.    Fenders- May bolt fenders to wheel wells up to 8 3/8inch bolts front and back. May fold fenders and weld. If you weld them you can?t use the bolts. If you bolt them you can?t weld them. The fenders CANNOT be welded to the frame.

8.    Windows- Windshield may have 2 bars 3inch wide 3/8inch thick max no more than 6inch on the firewall and cannot touch the straps from the dash bar and 6inch on roof. May connect with 2 bars 3inch by 3/8inch max. Cannot be connected to any hood or trunk bolt. Rear window may have 1 3inch by 3/8inch max c channel No more than 6inch on roof and 6inch past the trunks top seam. You may have no. 9 wire in 2 spots in each window.

9.    BUMPERS- If you decide to manufacture a homemade bumper it must conform to the following size limits: It can be no larger than 8inch by 8inch. The point must taper over an area of AT LEAST 32inch. Overall the bumper cannot exceed 12inch wide at the tip of the point. The point may only extend out 4inch past the flat part of the bumper. The bumper must be completely in front of frame rails. No part of the bumper may extend back past the furthest forward most point of the frame. Any factory bumper bracket or a 4 by wide to front part of the A arm bracket with a 3/8 thick flat stock.

10. Drive Train- Motor and tranny of choice, in stock location. Maybe welded or chained, the motor tie down CANNOT exceed 2inch in front or behind the heads to top of frame only 2 by 3/8 flat stock and cannot be laid flat on frame. No hold downs on back of motor when using a dp or mid plate. Dp can be touching firewall. Mid plates cannot be tied to the frame in any way or be wider than the motor. No extreme type full engine protectors. Engine cradles can be a max of 1/2 inch.

11. Suspension- Floater rear ends are ok, double coils are o.k. on coil cars. Leaf spring cars have up to 9 leafs per side and maybe clamped in 6 spots per side. Must be factory springs out of a car and CANNOT be home made. Rear end maybe chained in 2 spots per side of car. Coil springs may be wired in. Upper and lower trailing arms maybe reinforced, but they still have to function in a factory manor. The 99 and newer can change the rear suspension to the older style system. The 03 and newer cannot NOT change the front cradle must remain stock. A-arms cannot be welded to the frame in anyway no adding brackets and can run a gear box. Front suspension may be welded down with 2- 2 by 5inch 1/4inch long straps DO NOT weld them to the a arm?s must be frame to frame or bolted or spring spacers for height. Lower a arm can have a bar from lower a arm to bottom of frame and cannot go up the side of the frame in any way. Tie rods can be reinforced. A arms must be stock. Tires you may run any tire you see fit do whatever you have to do to not get a flat.

12. Frame repairs- If frame is rusted you may fix it with same thickness plate 1 inch past the rust hole (Don?t CUT THE RUST SPOT OUT). You may weld a plate 1inch past a bend. 20 inch max per side no longer than 6inches long pieces in the front of the car and 10 inches long in the back of car and must have a 1 inch gap between plates and welds cannot touch one side of frame only with a 1/4 plate only. Floor repairs must be sheet metal only or you won't run.

Economy Class Rules
Any car up to 108" rwd *NO FULL FRAME* or up to 113" fwd max

1.    Cage- Dash bar and behind seat bar and door bars allowed 2 inch min. diameter or square cannot be attached to frame. You may run a bar from dash bar to the firewall in 2 spots. Must be securely fastened or you will be told to remove. Halo bar no farther back then 10 inches from seat. Can be welded to frame and bolted to roof. Halo bar can be attached to the door bars. You can have 2 down bars from the door bars only located within the front inside door seam and straight down to rocker area. You can run a gas tank protector that must mount from the behind the seat bar 30inch wide and can go to the sheet metal and has to be 2 inches from the floor with no down bars DO NOT WELD TO SHEET METAL!

2.    Doors- **Please reinforce your driver?s door very good, in this type of competition all drivers doors will take some type of hit during the event. We want you to be safe and protected behind your reinforcement.  ** All doors may be welded solid with 3inch wide by 1/8inch thick strap or chained shut. Top of doors can be folded and welded together with no added metal.

3.    Hood and Trunk- Hood may be bolted in 8 spots, 4 to frame and 4 to sheet metal. The rod must be welded to top of frame do not go thru the frame or welded down the side must be vertical. Trunk lid may be welded solid with 3inch by 1/8inch thick strap or bolted every 3inch. Trunk may be bolted in 4 spots. Trunk may have 2 10inch by 4inch ¼inch strap from bumper to the trunk. You may tuck trunks. NO sedagons, decking must be removed.

4.    Seam welding- Frame can be welded fire wall forward top and bottom. Body seams can be welded 6 on 6 off Firewall forward.

5.    Body bolts- You may remove pucks. ALL bolts can be a max of 1 inch.

6.    Core support may have a 2 by 2 ¼inch angle iron on the top of core support from fender to fender. Radiator barrels are o.k. BUT must be factory size, CANNOT touch the frame in any way, CANNOT be welded to the angle iron at all, Bolted in 4 spots to core support or 4-2inch welds to core support to hold it in place. Must run vent tub under the car!

7.    Fenders- May bolt fenders to wheel wells up to 8 3/8inch bolts front and back. May fold fenders and weld. Rear window may have 2 - 2inch by 3/8inch c channel max. No more than 6inch on roof and 6inch on trunk or speaker deck. You may have 9 wire in 2 spots in each window.

8.    BUMPERS-Bumpers may be bolted or welded solid. You may fully weld bumpers and brackets. Nothing can be put inside of frame to mount the bumper in the compact class unless it's a factor bumper bracket. Midsize may a 4 long inch piece of square tubing to help hold bumper on. Bumpers are interchangeable with any mass produced car bumper. Stock appearing bumpers: we will allow you to take any bumper apart, weld any material you would like to the inside of bumper and weld the chrome back on. Everything must be done inside of bumper nothing on the outside. Compact bumper brackets ONLY NO full size brackets.

9.    Drive Train- Motor and tranny of choice in stock location. No V8s. Maybe welded or chained, the motor tie down CANNOT exceed 2inch in front or behind the heads to top or side of frame 2 by 3/8 flat stock and cannot be laid flat on frame. Engine cradles are ok in the compacts only 1/2 max but must have stock motor mounts. No cradles in the Economy class. No full engine protectors.

10. Suspension- Rear suspension must remain stock; double coils are o.k. on coil cars. Leaf spring cars have up to 7 leafs per side and maybe clamped in 6 spots per side. Must be factory springs out of a car and CANNOT be home made. Rear end maybe chained in 2 spots per side of car. Coil springs may be wired in. Upper and lower trailing arms maybe reinforced, but they still have to function in a factory manor. The Front suspension may be welded with 2- 2inch straps DO NOT strengthen frame or bolted or spring spacers for height. Tie rods maybe reinforced, but must function in a factory manor. Tires you may run any tire you see fit, foam it, double it whatever you have to do to not get a flat.

11. Frame repairs- If frame is rusted you may fix it with same thickness plate 1 inch past the rust hole (DO NOT CUT RUST SPOT OUT). You may weld a plate 1inch past a bend. 20 inch max per side, no longer than 8 inches long and must have a one inch gap between plates and welds cannot touch one side 1/4 inch only. Floor repairs must be sheet metal only or you won't run.

Builder Class Rules

 "Old iron and 80s and newer will run together under these rules"

1.    Cage- Dash bar and behind seat bar and door bars allowed 2 inch min and 5inch max diameter and cannot be attached to frame. May have only 2 bars max; behind seat in a crisscross pattern. Must be securely fastened or you will be told to remove. Dash bar may connect to the firewall in 2 spots 3inch by 3/8inch max flat stock and cannot be placed within the dp. If you have a dp or mid plate, dash bar must be 6 inch away from firewall. If you have a tranny brace it must be mounted to cross member with factory tranny mount, free floating or 1 bolt to tranny mount. Dash bar must be 2 inches away from tranny tunnel. Halo bar can be welded to frame and door bar. You can have 2 down bars from the door bars only located within the dash bar and behind the seat bar and straight down to rocker area 1 door bar per side can go to the frame. You can run a gas tank protector that must mount from the behind the seat bar 30inch wide and can go to the sheet metal but must be within the frame rails with no down bars and be off the floor 2inches.

2.    Doors- **Please reinforce your driver?s door very well, in this type of competition all drivers doors will take some type of hit during the event. We want you to be safe and protected behind your reinforcement.** All doors may be welded solid with 3inch wide by 1/8inch thick strap or chained shut. Top of doors can be folded and welded together with no added metal.

3.    Hood and Trunk- Hood may be bolted in 8 spots, 4 to frame and 4 to sheet metal. The rod must be welded to top of frame and cannot run down the frame in any way where it touches is it. The back hood bolts can have a 4inch by ¼inch thick triangle gusset to help attach the rod to the frame on top. Trunk lid may be welded solid with 3inch by 1/8inch thick strap or bolted every 3inch. Trunk may be bolted in 6 spots 4 to frame and 2 to sheet metal. Trunk may have a 10inch by 4inch ¼inch strap from bumper to the trunk. You may tuck trunks. NO sedagons, decking must have a 12 by 12 hole in it for inspection.

4.    Seam welding- Frame can be welded fire wall forward top and bottom. Body seams can be welded 6 on 6 off. K-frame CAN be welded solid, May take out pucks and replace with 1inch bolts. Y framer can plate the y's.

5.    Body bolts- You may remove pucks front and back, you may add 3 extra body bolts per side which can also go to frame with a max of 6inch by 6inch washer?s DO NOT WELD TO ANYTHING. ALL bolts can be a max of 1 inch.

6.    Core support- Core support may have a 2 by 2 ¼inch angle iron on the top of core support from fender to fender. Radiator barrels are o.k. Bolted in 4 spots to core support or 4-2inch welds to core support to hold it in place. Must run vent tub under the car!

7.    Fenders- May bolt fenders to wheel wells up to 8 3/8inch bolts front and back. May fold fenders and weld. You may weld the front clip solid. The fenders CANNOT be welded to the frame.

8.    Windows- Windshield may have 2 bars 3 inch wide no more than 6inch on the firewall and 6inch on roof; may connect with 2 bars 3inch by 3/8inch max. Cannot be connected to any hood or trunk bolt. Rear window may have 2, 3 inch c channel by 3/8inch max. No more than 6inch on roof and 6inch on trunk or speaker deck. You may have number 9 wire in 2 spots in each window.

9.    BUMPERS- If you decide to manufacture a homemade bumper it must conform to the following size limits: It can be no larger than 8inch by 8inch. The point must taper over an area of AT LEAST 32inch. Overall the bumper cannot exceed 12inch wide at the tip of the point. The point may only extend out 4inch past the flat part of the bumper. The bumper must be completely in front of frame rails. No part of the bumper may extend back past the furthest forward most point of the frame. Any factory automotive bumper bracket is allowed or a 4 by wide to front part of the A arm bracket with a 3/8 thick flat stock.

10. Drive Train- Motor and tranny of choice. Maybe welded or chained, the motor tie down CANNOT exceed 2inch in front or behind the heads to top or side of frame 2 by 3/8 flat stock and cannot be laid flat on frame. Dp can be touching firewall. You can run a 2 by 2 bar from dash bar to dp on old iron cars only. Can run 3/8inch X 2inch flat stock hold downs from the midplate to the frame, only 1 per side. Mid plates cannot be wider than the motor. Trany cross member can be 3 inch c channel with no bigger than a 4 by 5 plate on the ends to mount it to the frame. Full engine protectors can only be tied to the engine cross member. Engine cradles 1 inch cradles OK 5\8inch max for add-ons, head plate, mid plate ?no wider then motor" and dp.

11. Suspension- Rear suspension must remain stock; full floater rear ends are ok. Double coils are o.k. on coil cars. You may leaf or run a 30 inch hump plate that has to fallow the outside contour of the frame. You have up to 9 leafs per side and maybe clamped in 6 spots per side. Must be factory springs out of a car or light truck. Rear end maybe chained in 2 spots per side of car. Coil springs may be wired in. Upper and lower trailing arms maybe reinforced, they still have to function in a factory manor. The Front suspension may be welded with 2- 2inch by 5 straps DO NOT strengthen frame or a arms that can bolted or use spring spacers for height. Tie rods maybe reinforced, but must function in a factory manor. 03 and newer can change aluminum cradle to steel. NO IMP OR DOBA CRADDLES. A arms cannot be reinforced. Tires you may run any tire you see fit foam it, double it whatever you have to do to not get a flat.

12. Frame repairs- If frame is rusted you may fix it with same thickness plate 1 inch past the rust hole (Don?t CUT THE RUST SPOT OUT). You may weld a plate 1inch past a bend. 20 inches max per side no longer than 6inches long pieces in the front of the car and 10 inches long in the back of car and must have a 1 inch gap between plates no doubling up plates one side of frame only with a 1/4 plate only. Floor repairs must be sheet metal only or you won?t run. Frame swaps are ok. 

Chain Truck Rules

This class is stock other than stated below. Truck must be prepared as stated in the general rules.

1.    Any 1974 or newer 2wd, 4wd, 1/2, 3/4, pick up, blazer, suburban, or van is allowed. Frame height 7inch max. No one ton, camper or ambulance frames. 4wd need to remove a driveshaft. 

2.    No welding, cutting, or bending frame unless specified elsewhere. 

3.    Bumpers - stock or a maximum 4inch X 4inch square tubing behind a factory skin and back bumper will be allowed. Front bumper may be any OEM bumper welded on one 4 inch by 4 inch gusset on each side. No Ag Bumpers.  Stuffed bumpers are allowed.

4.    Stock gas tanks must be removed. Steel tanks must be securely fastened and covered in the front center of box or rear passenger area. Gas line through box, cab, and firewall must be steel. 

5.    Ignition may be moved to be used with toggle switches and push button. 

6.    Shifters may be modified to floor 

7.    Tailgates must be chained in six spot, with 2 around the frame or bumper. May weld 1-1/4inch thick X 2inch tall X 2inch wide X 3? long angle iron from the bottom of the tailgate to the box floor.

8.    Up to 4 -1/2 inch bolts may be used to hold box and cab together. 4 extra bolts holding cab to frame must be used for driver?s safety. No replacing or adding box bolts allowed. 

9.    Only 1 battery is allowed, securely fastened in the front passenger area. 

10. Hood may be secured with up to 6 chains; only 2 can be around frame or bumper. 

11. Tranny cooler may be relocated inside cab and must be covered. 

12. Welded or Posi type rear-ends allowed. 

13. Dash bar seat bar and windshield bar are required. 

14. Driver?s door bar is MANDATORY. You may have roll loop welded to frame and attached to the cab, no farther back than 10 inches from the back of the driver?s seat. No kickers. 

15.  Any tires are ok; split rims must be welded well. 

16. Driver's window must have safety net. 

17. Exhaust may be through hood, if not you must cut 12 inch by 12 inch hole for fire suppression. 

18. 2 chains per door seam. Driver?s door may be welded solid and have safety brace. 

19. Any engine and tranny allowed, solid motor mounts, reinforcing frame.

20. Bumpers and wheel wells may be trimmed. 

21. Suspension and drive train must be stock for model year. 

No body or suspension lifts allowed. Any lifts must be removed prior to entering the event.

80's & Newer Chain Rules

1.    Headers through hoods allowed.

2.    Stock gas tanks must be removed.

3.    Any car allowed ? Mopar 1980 and newer, Ford 1980 and newer, all GM 1977 and newer (METRIC CARS ONLY).

4.    Any tire is allowed.

5.    Radiator barrels are ok but must be bolted ONLY not welded in 4 spots and cannot touch the frame in any way. If for any reason you use the barrel to strengthen frame or car you will remove it or you can?t run. PLEASE don?t abuse this!!

6.    Transmission coolers are acceptable inside or outside, the car but must have approved steel or hydraulic hose.

7.    Original gas tanks must be removed. You must use a boat tank or well made fuel cell and it must be secured and covered. No plastic tanks or gas cans. Fuel line must be secured and fastened properly. Floating gas tank protector is allowed, must be attached to the seat bar no more than 24inch wide and must be at least 10inch away from the rear tin. Tank must be fastened down securely; no plumber?s strap, bungee straps or self tapping screws.

8.    Bumper may be welded to Shocks may be welded, bolted or chained to frame, so we don?t have loose bumpers on the track. You may trim ends. Bumpers are interchangeable. NO Chrysler v bumpers. Bumper brackets must be factory to the car. No loaded bumpers.

9.    Windshield screen is also highly recommended

10. If not running stacks through the hood a hole must be cut for fire safety.

11. Trunk lids and hood may be fastened in 6 places with chain 3/8 inch, 4 loops maximum.

12. Driver?s door may be welded shut, all others chained with 3/8 inch chain, 2 per seam. No welding of any other doors but driver?s door. The bottom of the door seams may be chained threw the door and around the frame. Number 9 wire is ok.

13. Frames must remain factory stock. NO tilting of any car up front in any way.

14. Stock suspensions must be left intact. No welding up A arms or tie rods.

15. Batteries must be placed in the passenger?s side floorboard and secured and covered. Must be placed as close to the center of the vehicle as possible. Any 12 volt battery safely in the car is allowed.

16. Ignition switches and push-button starts are optional (wire it up so it works).

17. Body mounts must remain in position between the frame and the body. Front hood bolts are allowed thru the factory body mounts only with a 4 inch spacer, 3/8 inch threaded rod max.

18. No welding leaf springs or adding extra leafs. 

19. No welding body seams.

20. Cutting for wheel clearance is allowed.

21. Homemade shifters allowed.

22. Driver?s side window nets recommended.

23.  Motors are interchangeable.

24. Dash Bars are recommended! 4 point cage is o.k. for safety

25. Protectors, lower engine cradles or slider drive shafts are not allowed. If it is not a part from the automotive factory you can?t run it. 

Members Area

Upcoming Events

No upcoming events

Newest Members

Testimonials