Top Notch Motorsports LLC

Click here to edit subtitle

Perham

East Otter Tail County Fair

Perham, MN on July 22nd @ 6 pm

Compact trucks "weld" -  1st $2000, 2nd $750, 3rd $250, 4th $50

Economy Class -  1st $2000, 2nd $750, 3rd $250, 4th $50

Builder Class - 1st $2000, 2nd $750, 3rd $250, 4th $50 

General Rules

1. All drivers are required to wear seat belts, safety helmet, and eye protection. Neck brace is optional but recommended.

2. All cars must be standard make with no reinforcement or alterations to the frame unless specified. 

3. You must remove all glass, mirrors, trailer hitches and chrome.

4. Car or truck must have 12"x12" hole cut in hood in case of fire.

5. Brakes must be in working order. Minimum of 2 working brakes.

6. Gas tank (steel only-no plastic) covered and strapped in the back seat or box. MUST HAVE FUEL CUT OFF WITH ELECTRIC FUEL PUMP (steel strapping or chains-no bungee cords on gas tank or battery).

7. Batteries covered and strapped in passenger seat area. MUST BE COVERED FOR YOUR PROTECTION.

8. One fire-you start; second fire-disqualification.

9. You have 20 seconds to make an aggressive hit, 2 minutes to get vehicle started.

10. No intentional crashing of the driver’s door, subject to disqualification.

11. Vehicles must continue to crash. No avoiding, holding, tag-teaming or sandbagging. No using drivers door as a block.

12. No riding on vehicles at any time. Drivers must remain inside vehicle during derby and when being towed, except for fires.

13. Drivers door may be welded solid or reinforced in any way for safety, a window net or strapping is recommended

14. Radiators must remain in stock position. Transmission coolers allowed.

15. Driver is responsible for any member of his or her pit crew. Any rules found violated will result in disqualification of driver, pit crew, and car and will forfeit any winnings, entry fee, and trophies.

16. **** NO DRUGS OR ALCOHOLIC BEVERAGES IN PIT AREA BEFORE OR DURING THE DERBY. SUBJECT TO ARREST AND DISQUALIFICATION. THIS IS ENFORCED!!!!!

17. For the derby all automobiles are acceptable except 1973 and older Imperials or convertibles. NO CARS WITH IMP SUB FRAMES.

18. **** NO GREY AREA OR TECHNICAL BUILDING!!! IF YOU’RE TOLD TO CUT AND REFUSE TO YOU WILL LOAD YOUR CAR AND WILL NOT RUN. WE WILL NOT TOUCH YOUR CAR AFTER IT LEAVES THE TECH LINE AFTER REFUSAL TO CUT.

19. All cars must have an electric shut off



Compact truck and minivan rules

1. CAGE. Must have a cage inside of truck. You may have 1 down bar per side. Dash bar can have a kicker to frame no farther forward then firewall inside the cab. You may also have a roll loop in the box up against the cab with kickers no farther back then the center of the axle.

2. Doors. **Please reinforce your driver’s door very good, in this type of competition all drivers doors will take some type of hit during the event. We want you to be safe and protected behind your reinforcement.** All doors may be welded solid with 3” wide by 1/8” thick strap or chained shut. Top of doors can be folded and welded together with no added metal.

3. . Hood and Tail gate- Hood may be bolted in 6 spots. 2 to frame and 4 to sheet metal. The rod can go down the side of frame but must be vertical. Tailgates must be welded or taken off. You may use a piece of 3ft max of angle iron on the inside to hold the tail gate on.

4. Body Bolts- You may remove pucks front and back, you may add 4 extra body bolts per side which can also go to frame with a max of 6”x 6” washer’s and a 1inch bolt washers. Washers cannot be welded to frame or sheet metal.

5.Radiator- Radiator barrels are o.k. Must run vent tub under the car!

6.Fenders- May bolt fenders to wheel wells up to 8 3/8" bolts front and back. May fold fenders or weld.

7 Windows- Windshield may have 2 bars 3” wide 3/8” thick max no more than 6” on the firewall and 6” on roof. May connect with 2 bars 3” by 3/8” max. Cannot be connected to any hood or bolts.

8. BUMPERS- Front bumper can be no more than 27” from the ground to the top of the bumper. Bumpers may be bolted or welded solid. You may fully weld bumpers and brackets. Bumpers are interchangeable with any mass produced car bumper. Stock appearing bumpers: we will allow you to take any bumper apart, weld any material you would like to the inside of bumper and weld the chrome back on. Everything must be done inside of bumper nothing on the outside. NO home made bumpers must be a factory bumper. You may use a 16inch by 4 1/4inch strap to hold the bumper on or any automotive bumper bracket.

9. Drive Train- Motor and tranny of choice, in stock location V8‘s are allowed. Maybe welded or chained, the motor tie down CANNOT exceed 2” in front or behind the heads to top of frame only 2 by 3/8 flat stock and cannot be laid flat on frame. Engine craddles are ok. The front driveshaft must be removed on a 4 wheel drive truck.

10. Suspension- May have up to 9 leafs per side and maybe clamped in 6 spots per side. Must be factory springs out of a compact truck and CANNOT be home made. Rear end maybe chained in 2 spots per side of car. Coil springs may be wired in. Upper and lower trailing arms maybe reinforced, but they still have to function in a factory manor. . Front suspension may be welded down with a 2- 2inch wide by 1/4inch thick straps and cannot be welded to the a arm. Lower a arm can have a bar from lower a arm to bottom of frame and cannot go up the side of the frame in any way. Tie rods can be reinforced and a arms must be stock. Tires you may run any tire you see fit, foam it, double it what ever you have to do to not get a flat.

11. Frame repairs- Modifying Spindles forward is ok. If frame is rusted you may fix it with same thickness plate 1 inch past the rust hole (DO NOT CUT THE RUST SPOT OUT). You may weld a plate 1” past a bend. Must have a 1 inch gap between plates and welds cannot touch one side of frame only with a 1/4 plate only. Floor repairs must be sheet metal only or you won’t run.


Economy Class Rules

(any car up to 108" rwd **NO FULL FRAME** or up to 113" fwd max)


1.    Cage- Dash bar and behind seat bar and door bars allowed 2 inch min. diameter or square cannot be attached to frame. You may run a bar from dash bar to the firewall in 2 spots. Must be securely fastened or you will be told to remove. Halo bar no farther back then 10 inches from seat. Can be welded to frame and bolted to roof. Halo bar can be attached to the door bars. You can have 2 down bars from the door bars only located within the front inside door seam and straight down to rocker area. You can run a gas tank protector that must mount from the behind the seat bar 30inch wide and can go to the sheet metal and has to be 2 inches from the floor with no down bars DO NOT WELD TO SHEET METAL!
Must be securely fastened or you will be told to remove. Halo bar no farther back then 10 inches from seat. Can be welded to frame and bolted to roof. Halo bar can be attached to the door bars. You can have 2 down bars from the door bars only located within the front inside door seam and straight down to rocker area. You can run a gas tank protector that must mount from the behind the seat bar 30inch wide and can go to the sheet metal and has to be 2 inches from the floor with no down bars DO NOT WELD TO SHEET METAL!
2.    Doors- **Please reinforce your driver's door very good, in this type of competition all drivers doors will take some type of hit during the event. We want you to be safe and protected behind your reinforcement.  ** All doors may be welded solid with 3" wide by 1/8" thick strap or chained shut. Top of doors can be folded and welded together with no added metal.
3.    Hood and Trunk- Hood may be bolted in 8 spots, 4 to frame and 4 to sheet metal. The rod must be welded to top of frame do not go thru the frame or welded down the side must be vertical. Trunk lid may be welded solid with 3" by 1/8" thick strap or bolted every 3inch. Trunk may be bolted in 4 spots. Trunk may have 2 10" by 4" ¼" strap from bumper to the trunk. You may tuck trunks. NO sedagons, decking must be removed.
4.    Seam welding- Frame can be welded fire wall forward top and bottom. Body seams can be welded 6 on 6 off Firewall forward.
5.    Body bolts- You may remove pucks. ALL bolts can be a max of 1 inch.
6.    Core support may have a 2 by 2 ¼" angle iron on the top of core support from fender to fender. Radiator barrels are o.k. BUT must be factory size, CANNOT touch the frame in any way, CANNOT be welded to the angle iron at all, Bolted in 4 spots to core support or 4-2" welds to core support to hold it in place. Must run vent tub under the car!
7.    Fenders- May bolt fenders to wheel wells up to 8 3/8" bolts front and back. May fold fenders and weld. Rear window may have 2 - 2" by 3/8" c channel max. No more than 6" on roof and 6" on trunk or speaker deck. You may have 9 wire in 2 spots in each window.
8.    BUMPERS-Bumpers may be bolted or welded solid. You may fully weld bumpers and brackets. Nothing can be put inside of frame to mount the bumper in the compact class unless it's a factor bumper bracket. Midsize may a 4 long inch piece of square tubing to help hold bumper on. Bumpers are interchangeable with any mass produced car bumper. Stock appearing bumpers: we will allow you to take any bumper apart, weld any material you would like to the inside of bumper and weld the chrome back on. Everything must be done inside of bumper nothing on the outside. Compact bumper brackets ONLY NO full size brackets.
9.    Drive Train- Motor and tranny of choice in stock location. No V8s. Maybe welded or chained, the motor tie down CANNOT exceed 2" in front or behind the heads to top or side of frame 2 by 3/8 flat stock and cannot be laid flat on frame. Engine cradles are ok in the compacts only 1/2 max but must have stock motor mounts. No cradles in the Economy class. No full engine protectors.
10. Suspension- Rear suspension must remain stock; double coils are o.k. on coil cars. Leaf spring cars have up to 7 leafs per side and maybe clamped in 6 spots per side. Must be factory springs out of a car and CANNOT be home made. Rear end maybe chained in 2 spots per side of car. Coil springs may be wired in. Upper and lower trailing arms maybe reinforced, but they still have to function in a factory manor. The Front suspension may be welded with 2- 2" straps DO NOT strengthen frame or bolted or spring spacers for height. Tie rods maybe reinforced, but must function in a factory manor. Tires you may run any tire you see fit, foam it, double it whatever you have to do to not get a flat.
11. Frame repairs- If frame is rusted you may fix it with same thickness plate 1 inch past the rust hole (DO NOT CUT RUST SPOT OUT). You may weld a plate 1" past a bend. 20 inch max per side, no longer than 8 inches long and must have a one inch gap between plates and welds cannot touch one side 1/4 inch only. Floor repairs must be sheet metal only or you won't run.

Builder's class rules

"Old iron and 80s and newer will run together under these rules"

1. Cage- Dash bar and behind seat bar and door bars allowed 2 inch min and 5inch max diameter and cannot be attached to frame. May have only 2 bars max; behind seat in a crisscross pattern. Must be securely fastened or you will be told to remove. Dash bar may connect to the firewall in 2 spots 3" by 3/8" max flat stock and cannot be placed within the dp. If you have a dp or mid plate, dash bar must be 6 inch away from firewall. If you have a tranny brace it must be mounted to cross member with factory tranny mount, free floating or 1 bolt to tranny mount. Dash bar must be 2 inches away from tranny tunnel. Halo bar can be welded to frame and door bar. You can have 2 down bars from the door bars only located within the dash bar and behind the seat bar and straight down to rocker area 1 door bar per side can go to the frame. You can run a gas tank protector that must mount from the behind the seat bar 30" wide and can go to the sheet metal but must be within the frame rails with no down bars and be off the floor 2inches.

2. Doors- **Please reinforce your driver's door very well, in this type of competition all drivers doors will take some type of hit during the event. We want you to be safe and protected behind your reinforcement.** All doors may be welded solid with 3" wide by 1/8" thick strap or chained shut. Top of doors can be folded and welded together with no added metal.

3. Hood and Trunk- Hood may be bolted in 8 spots, 4 to frame and 4 to sheet metal. The rod must be welded to top of frame and cannot run down the frame in any way where it touches is it. The back hood bolts can have a 4" by ¼" thick triangle gusset to help attach the rod to the frame on top. Trunk lid may be welded solid with 3" by 1/8" thick strap or bolted every 3inch. Trunk may be bolted in 6 spots 4 to frame and 2 to sheet metal. Trunk may have a 10" by 4" ¼" strap from bumper to the trunk. You may tuck trunks. NO sedagons, decking must have a 12 by 12 hole in it for inspection.

4. Seam welding- Frame can be welded fire wall forward top and bottom. Body seams can be welded 6 on 6 off. K-frame CAN be welded solid, May take out pucks and replace with 1" bolts. Y framer can plate the y's.

5. Body bolts- You may remove pucks front and back, you may add 3 extra body bolts per side which can also go to frame with a max of 6"x 6" washer's DO NOT WELD TO ANYTHING. ALL bolts can be a max of 1 inch.

6. Core support- Core support may have a 2 by 2 ¼" angle iron on the top of core support from fender to fender. Radiator barrels are o.k. Bolted in 4 spots to core support or 4-2" welds to core support to hold it in place. Must run vent tub under the car!

7. Fenders- May bolt fenders to wheel wells up to 8 3/8" bolts front and back. May fold fenders and weld. You may weld the front clip solid. The fenders CANNOT be welded to the frame.

8. Windows- Windshield may have 2 bars 3 inch wide no more than 6" on the firewall and 6" on roof; may connect with 2 bars 3" by 3/8" max. Cannot be connected to any hood or trunk bolt. Rear window may have 2, 3 inch c channel by 3/8" max. No more than 6" on roof and 6" on trunk or speaker deck. You may have number 9 wire in 2 spots in each window.

9. BUMPERS- If you decide to manufacture a homemade bumper it must conform to the following size limits: It can be no larger than 8"x8". The point must taper over an area of AT LEAST 32". Overall the bumper cannot exceed 12" wide at the tip of the point. The point may only extend out 4" past the flat part of the bumper. The bumper must be completely in front of frame rails. No part of the bumper may extend back past the furthest forward most point of the frame. Any factory automotive bumper bracket is allowed or a 4 by wide to front part of the A arm bracket with a 3/8 thick flat stock.

10. Drive Train- Motor and tranny of choice. Maybe welded or chained, the motor tie down CANNOT exceed 2" in front or behind the heads to top or side of frame 2 by 3/8 flat stock and cannot be laid flat on frame. Dp can be touching firewall. You can run a 2 by 2 bar from dash bar to dp on old iron cars only. Can run 3/8" X 2" flat stock hold downs from the midplate to the frame, only 1 per side. Mid plates cannot be wider than the motor. Trany cross member can be 3 inch c channel with no bigger than a 4 by 5 plate on the ends to mount it to the frame. Full engine protectors can only be tied to the engine cross member. Engine cradles 1 inch cradles OK 5\8" max for add-ons, head plate, mid plate "no wider then motor" and dp.

11. Suspension- Rear suspension must remain stock; full floater rear ends are ok. Double coils are o.k. on coil cars. You may leaf or run a 30 inch hump plate that has to fallow the outside contour of the frame. You have up to 9 leafs per side and maybe clamped in 6 spots per side. Must be factory springs out of a car or light truck. Rear end maybe chained in 2 spots per side of car. Coil springs may be wired in. Upper and lower trailing arms maybe reinforced, they still have to function in a factory manor. The Front suspension may be welded with 2- 2inch by 5 straps DO NOT strengthen frame or a arms that can bolted or use spring spacers for height. Tie rods maybe reinforced, but must function in a factory manor. 03 and newer can change aluminum cradle to steel. NO IMP OR DOBA CRADDLES. A arms cannot be reinforced. Tires you may run any tire you see fit foam it, double it whatever you have to do to not get a flat.

12. Frame repairs- If frame is rusted you may fix it with same thickness plate 1 inch past the rust hole (Don't CUT THE RUST SPOT OUT). You may weld a plate 1" past a bend. 20 inches max per side no longer than 6 inches long pieces in the front of the car and 10 inches long in the back of car and must have a 1 inch gap between plates no doubling up plates one side of frame only with a 1/4 plate only. Floor repairs must be sheet metal only or you won't run. Frame swaps are ok.